Flash Sale LAUNCH X431 Creader Elite 2.0 Bi-Directional OBD2 Scanner for BMW Mercedes Benz AUDI VW,Full System Diagnostic,All Service,ECU Coding,Battery Register

Optimally code your vehicles by changing some settings to fit your needs, such as setting alarms, etc.

Access the ECU to make full use of the hidden features or dis-able the car’s annoying functions,

Provide excellent solutions for issues of drivability, power loss, f.uel efficiency, etc. to improve the car’s performance.

Reprogram the ad.aptive data for certain components after repairs or re-placements.

ABS Bleeding: When the ABS contains a.ir, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity

Oil Reset: Close the oil service light, reset service mileage & service interval after replacing the engine oil, and the next maintenance calculation cycle is entered.

Battery Registration: With the power battery system management system, when a car battery is replaced and needs to be re-matched, it enables the car computer to recognize the new battery. (Note: Batteries of the same type and capacity are supported, as well as batteries of different types and different capacities.)

Injector Coding: The engine injector has a code. After replacement, you need to write a new code into the computer so that the car computer can correctly identify the injector.

TPMS Reset: When replacing TPMS sensors or the signal from the sensor is lost it can quickly look up the tire sensor from the vehicle’s ECU, reset tire pressure and turn off the tire pressure MIL

Gear Learning: The vehicle has a crankshaft position sensor. This sensor collects the 58-tooth signal of the flywheel to determine the top dead center ignition time of a cylinder (reference signal). If this sensor is replaced, the reference will be lost, and gear signal learning is necessary.

EPB Reset (Electronic Parking Brake Reset): After replacing the brake pads, you need to reset the position of the brake pads before installing the new brake pads to close the warning light.

Throttle Calibration: A throttle position sensor is a sensor used to monitor the a.ir intake of an engine, which provides the ECU with information on whether the throttle is in the idle position, wide-open throttle (WOT) position, or somewhere in between these extremes. After the throttle is cleaned, the throttle opening needs to be re-adjusted to improve vehicle performance.

DPF Reset: Clear diesel particles from the filter through oxidation or combustion to stabilize the filter performance.--------------------------------More Hot Service Functions: 9. Clutch reset, 10. Gearbox adaptation, 11. Headlight initialization, 12. Crank sensor releam, 13. Power window initialization, 14. Power window regulators initialization, 15. Slide sunroof initialization, 16. Automatic engine start-stop, 17. Automatic tailgate actuation initialisation, 18. Delete transport mode, 19.Reset service interval indicator, 20. Calibrating and teaching system for all-round vision camera, 21.Fuel injector adaptation, 22. Fuel system Bleeding, 23. Fuel consumption display, 24.Brake bleeding procedure, 25. Rain sensor initialization, 26. Rain-light-solar-condensations sensor Initialisation, 27. Learn sensor zero point, 28. A/C compressor initialization, 29. EWS-DME/DDE adjustment, 30. SAS reset, 31. Injector rate adjustment, 32. Windscreen wipers - Installation position, 33.CAS reset, 34. Calibration of lane departure warning, 35. Change emergency number, 36. A.ir suspension height calibration , 37.Fuel pressure test, 38. Idle correction, 39.Initialise Front wipers, 40. Initialize FlexRay, 41. Initialized telematics services, 42. Learn Valvetronic Limit Positions, 43. Line Short Circuit Of FRM Reset, 44. Start-up of active steering, 45. Activate Bluetooth and emergency call, 46. Learn pressure sensors, 47.Start-up of ACC sensor, 48. CO adjustment, 49.Im-mo-biliser reset, 50.Reset adaptations, and etc. More Reset Function Continuously growing with updates...